1 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com technical data sheet 1.2mm round subminiature side looking infrared led EAISV3027A0 features ? small double-end package ? low forward voltage ? good spectral matching to si photo detector ? package in 8mm tape on 7 diameter reel. ? pb free ? the product itself will remain within rohs complian t version. ? compliance with eu reach. ? compliance halogen free .(br <900 ppm ,cl <900 ppm , br+cl < 1500 ppm) description ? EAISV3027A0 is an infrared emitting diode in miniat ure smd package which is molded in a water clear plastic with spherical top view lens. the dev ice is spectrally matched with silicon photodiode a nd phototransistor applications ? infrared applied system device selection guide device no. chip material lens color EAISV3027A0 gaalas water clear ver.:1 release date:08/21/2018 B:approved(?l)
datasheet EAISV3027A0 2 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com package dimensions notes: 1.all dimensions are in millimeters 2.tolerances unless dimensions 0.1mm absolute maximum ratings (ta=25 ) parameter symbol rating unit continuous forward current i f 50 ma peak forward current *1 i fp 500 ma reverse voltage v r 5 v operating temperature t opr -40 ~ +100 c storage temperature t stg -40 ~ +100 c soldering temperature *2 t sol 260 c power dissipation at(or below) 25 free air temperature p c 100 mw notes: *1: i fp conditions--pulse width Q Q Q Q 100 s and duty Q Q Q Q 1%. *2: soldering time Q Q Q Q 5 seconds. a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
datasheet EAISV3027A0 3 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com electro-optical characteristics (ta=25 unless specified otherwise) parameter symbol min. typ.* max. unit condition radiant intensity *1 i e 20.0 25.0 -- mw/sr i f =20ma -- 100.0 -- mw/sr i f =70ma pulse width Q 100 s duty Q 1% peak wavelength p -- 940 -- nm i f =20ma spectral bandwidth -- 30 -- nm i f =20ma forward voltage v f -- 1.30 1.60 v i f =20ma 1.50 2.00 v i f =70ma pulse width Q 100 s duty Q 1% reverse current i r -- -- 10 a v r =5v view angle 2 1/2 -- 15.0 -- deg. i f =20ma a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
datasheet EAISV3027A0 4 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com -40 -20 0 20 40 60 80 100 0 10 20 30 40 50 60 70 forward current(ma) ambient temperature ( o c) typical electrical/optical/characteristics curves forward current vs. ambient temperature spectral distribution radiant intensity vs forward current forward current vs. forward voltage a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
datasheet EAISV3027A0 5 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com relative radiant intensity vs. angular displacement a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
datasheet EAISV3027A0 6 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com precautions for use 1. over-current-proof customer must apply resistors for protection, other wise slight voltage shift will cause big current ch ange (burn out will happen). 2. storage 2.1 do not open moisture proof bag before the produ cts are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 60%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be k ept at 30 or less and 60%rh or less. 2.5 the leds should be used within 168 hours (7 day s) after opening the package. 2.6 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the stora ge time, baking treatment should be performed using th e following conditions. baking treatment : 60 5 for min. 24 hours. 3. soldering condition 3.1 pb-free solder temperature profile 3.2 reflow soldering should not be done more than t wo times. 3.3 when soldering, do not put stress on the leds d uring heating. 3.4 after soldering, do not warp the circuit board. a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
datasheet EAISV3027A0 7 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com 4. soldering iron each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do solder ing of each terminal. be careful because the damage of the product is often started at the time of the han d solder. 5. repairing repair should not be done after the leds have b een soldered. when repairing is unavoidable, a double-head soldering iron should be used (as below figure). it should be confirmed beforehand whether the characteristics of the leds will or will not be dam aged by repairing. a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
datasheet EAISV3027A0 8 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com package dimensions note: the tolerances unless mentioned is 0.1mm ,unit = mm carrier tape dimensions :( quantity: 1500pcs/reel) note: the tolerances unless mentioned is 0.1mm ,unit = mm a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
datasheet EAISV3027A0 9 copyright ? 2010, everlight all rights reserved. re lease date : aug.16.2018. issue no: dir-0002003 rev.1 www.everlight.com packing procedure aluminum moistue-proof bag label desiccant label label form specification cpn: customer?s production number p/n : production number qty: packing quantity cat: ranks hue: peak wavelength ref: reference lot no: lot number made in taiwan: production place disclaimer 1. everlight reserves the right(s) on the adjustment o f product material mix for the specification. 2. the product meets everlight published specification for a period of twelve (12) months from date of shipment. 3. the graphs shown in this datasheet are representing typical data only and do not show guaranteed value s. 4. when using this product, please observe the absolut e maximum ratings and the instructions for using outlined in these specification sheets. everlight a ssumes no responsibility for any damage resulting from the use of the product which does not comply w ith the absolute maximum ratings and the instructio ns included in these specification sheets. 5. these specification sheets include materials protec ted under copyright of everlight. reproduction in any form is prohibited without obtaining everlight? s prior consent. 6. this product is not intended to be used for militar y, aircraft, automotive, medical, life sustaining o r life saving applications or any other application which can result in human injury or death. please contact authorized everlight sales agent for special applic ation request. a wfs/;2!!!!!sfmfbtf!ebuf;1903203129!!!!!!bh0;bqqspwfe); .f$w?*
|
